commit 9e056ac0dc7c43380daf26af7c75ae35c44c61ae Author: lukas Date: Thu Jun 13 11:22:29 2024 +0000 Add printer.cfg diff --git a/printer.cfg b/printer.cfg new file mode 100644 index 0000000..c9ebdc2 --- /dev/null +++ b/printer.cfg @@ -0,0 +1,247 @@ +# This file contains pin mappings for the stock 2020 Creality Ender 3 +# MAX. To use this config, during "make menuconfig" select the +# STM32F103 with a "28KiB bootloader" and serial (on USART1 PA10/PA9) +# communication. + +# Because this printer has factory wiring, mounts, and firmware for +# a BLTouch, but does not ship with one at this time, default values +# for the sensor have been specified, but disabled, in anticipation of +# future revisions or user modification. User should take care to +# customize the offsets, particularly z-offset, for their specific unit. + +# If you prefer a direct serial connection, in "make menuconfig" +# select "Enable extra low-level configuration options" and select +# serial (on USART3 PB11/PB10), which is broken out on the 10 pin IDC +# cable used for the LCD module as follows: +# 3: Tx, 4: Rx, 9: GND, 10: VCC + +# Flash this firmware by copying "out/klipper.bin" to a SD card and +# turning on the printer with the card inserted. The firmware +# filename must end in ".bin" and must not match the last filename +# that was flashed. + +# See docs/Config_Reference.md for a description of parameters. + +[include mainsail.cfg] + +[stepper_x] +step_pin: PB9 +dir_pin: PC2 +enable_pin: !PC3 +microsteps: 16 +rotation_distance: 40 +endstop_pin: ^PA5 +position_endstop: -4 +position_min: -4 +position_max: 301 +homing_speed: 50 + +[stepper_y] +step_pin: PB7 +dir_pin: PB8 +enable_pin: !PC3 +microsteps: 16 +rotation_distance: 40 +endstop_pin: ^PA6 +position_endstop: -9 +position_min: -9 +position_max: 304 +homing_speed: 50 + +[stepper_z] +step_pin: PB5 +dir_pin: !PB6 +enable_pin: !PC3 +microsteps: 16 +rotation_distance: 2 +#position_endstop: 0.0 # disable to use BLTouch +#endstop_pin: ^PA7 # disable to use BLTouch +endstop_pin: probe:z_virtual_endstop # enable to use BLTouch +position_min: -5 # enable to use BLTouch +position_max: 340 + +[safe_z_home] # enable for BLTouch +home_xy_position: 150, 150 +speed: 100 +z_hop: 10 +z_hop_speed: 5 + +[bltouch] # enable for BLTouch - fast-mode +sensor_pin: ^PB1 +control_pin: PB0 +pin_up_touch_mode_reports_triggered: True +probe_with_touch_mode: True +x_offset: 50 # modify as needed for bltouch location +y_offset: -6 # modify as needed for bltouch location +#z_offset: 0.0 # modify as needed for bltouch or run PROBE_CALIBRATE +speed: 10 +samples: 3 +sample_retract_dist: 5.0 # Can be set lower, example 2.5 depending on height of bltouch from bed +lift_speed: 40 +samples_tolerance_retries: 3 +speed: 10 +samples: 2 + +[bed_mesh] # enable for BLTouch +speed: 300 +mesh_min: 50, 6 +mesh_max: 295, 295 +algorithm: bicubic +probe_count: 7,7 # 49 points due to large bed size +horizontal_move_z: 5 + + +[gcode_macro G29] # If moving from marlin to klipper uncomment to mimic G29 +gcode: + BED_MESH_CALIBRATE + G1 X0 Y0 Z10 F4000 + +[extruder] +max_extrude_only_distance: 100.0 +step_pin: PB3 +dir_pin: PB4 +enable_pin: !PC3 +microsteps: 16 +rotation_distance: 31.901 # Calibrate - see https://www.klipper3d.org/Rotation_Distance.html +nozzle_diameter: 0.400 +filament_diameter: 1.750 +heater_pin: PA1 +sensor_type: EPCOS 100K B57560G104F +sensor_pin: PC5 +control: pid +pid_Kp: 21.527 +pid_Ki: 1.063 +pid_Kd: 108.982 +min_temp: 0 +max_temp: 250 +pressure_advance: 0.0 # Calibrate - see https://www.klipper3d.org/Pressure_Advance.html + + +[heater_bed] +heater_pin: PA2 +sensor_type: EPCOS 100K B57560G104F +sensor_pin: PC4 +control: pid +pid_Kp: 54.027 +pid_Ki: 0.770 +pid_Kd: 948.182 +min_temp: 0 +max_temp: 130 + +[fan] +pin: PA0 + +[filament_switch_sensor e0_sensor] +switch_pin: PA4 + +[mcu] +serial: /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0 # Run ls /dev/serial/by-id/* for micro-controller name +restart_method: command + +[printer] +kinematics: cartesian +max_velocity: 100 +max_accel: 500 +max_z_velocity: 5 +max_z_accel: 100 + +[display] +lcd_type: st7920 +cs_pin: PB12 +sclk_pin: PB13 +sid_pin: PB15 +encoder_pins: ^PB14, ^PB10 +click_pin: ^!PB2 + +[temperature_sensor mcu_temp] +sensor_type: temperature_mcu +min_temp: 0 +max_temp: 100 + +[temperature_sensor raspberry_pi_3b+] +sensor_type: temperature_host +min_temp: 0 +max_temp: 100 + +### menu virtual sdcard ### +[menu __main __sdcard] +type: list +enable: {'virtual_sdcard' in printer} +name: Files + +[menu __main __sdcard __file] +type: command +name: File: {printer.print_stats.filename} + +[menu __main __sdcard __load] +type: vsdlist +enable: {not printer.virtual_sdcard.file_path and not (printer.print_stats.state == "printing" or printer.print_stats.state == "paused")} +name: Load file + +[menu __main __sdcard __unload] +type: command +enable: {printer.virtual_sdcard.file_path and not (printer.print_stats.state == "printing" or printer.print_stats.state == "paused")} +name: Unload file +gcode: + {menu.back()} SDCARD_RESET_FILE + +[menu __main __sdcard __start] +type: command +enable: {printer.virtual_sdcard.file_path and not (printer.print_stats.state == "printing" or printer.print_stats.state == "paused")} +name: Start print +gcode: + {menu.exit()} + UPDATE_DELAYED_GCODE ID=_DELAY_DISPLAY_OFF DURATION=10 + M24 + +[menu __main __sdcard __pause] +type: command +enable: {printer.print_stats.state == "printing"} +name: Pause print +gcode: + {menu.back()} PAUSE + +[menu __main __sdcard __resume] +type: command +enable: {printer.print_stats.state == "paused"} +name: Resume print +gcode: + {menu.exit()} + UPDATE_DELAYED_GCODE ID=_DELAY_DISPLAY_OFF DURATION=10 + RESUME + +[menu __main __sdcard __cancel] +type: command +enable: {printer.print_stats.state == "paused"} +name: Cancel print +gcode: + {menu.exit()} + UPDATE_DELAYED_GCODE ID=_DELAY_DISPLAY_OFF DURATION=10 + CANCEL_PRINT + +#*# <---------------------- SAVE_CONFIG ----------------------> +#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated. +#*# +#*# [bltouch] +#*# z_offset = 2.920 +#*# +#*# [bed_mesh default] +#*# version = 1 +#*# points = +#*# 0.102187, 0.088437, 0.054687, -0.043438, -0.046250, -0.109375, -0.084375 +#*# 0.061562, 0.068750, 0.048437, 0.041875, 0.056562, -0.085938, -0.132500 +#*# 0.047500, 0.045000, 0.011250, -0.072813, -0.036563, -0.112813, -0.139063 +#*# -0.020938, -0.038438, 0.022187, -0.054688, 0.015625, -0.036250, -0.076250 +#*# -0.016875, -0.015625, -0.028438, -0.094375, -0.065938, -0.095313, -0.115938 +#*# -0.070000, 0.023750, 0.029375, 0.001875, -0.043438, -0.069375, -0.095313 +#*# -0.134688, -0.114375, -0.058750, -0.175625, -0.110625, -0.148438, -0.133750 +#*# x_count = 7 +#*# y_count = 7 +#*# mesh_x_pps = 2 +#*# mesh_y_pps = 2 +#*# algo = bicubic +#*# tension = 0.2 +#*# min_x = 50.0 +#*# max_x = 294.97 +#*# min_y = 6.0 +#*# max_y = 294.96