Merge branch 'detach' into 'master'

detach before call

See merge request lukas/pumpensteuerung!11

src/Heating.cpp

@@ -12,7 +12,6 @@ Heating::Heating() : mHeizungTicker(),
                      msettings(nullptr),
                      mheatingservice(nullptr),
                      mHeatingStatus(false),
-                     mPumpCycleActive(false),
                      lasttemp(0),
                      lasthum(0),
                      sensor() {}
@@ -33,8 +32,8 @@ void Heating::init(unsigned mode, const SettingState *settings, HeatingInfoServi
 
             sensor.onData([this](float hum, float temp) {
                 schedule_function([hum, temp, this]() {
-//                    Serial.printf("Temp: %gdegC\n", temp);
-//                    Serial.printf("Humid: %g%%\n", hum);
+                    Serial.printf("Temp: %gdegC\n", temp);
+                    Serial.printf("Humid: %g%%\n", hum);
 
                     mheatingservice->setSensorData(hum, temp);
 
@@ -56,16 +55,13 @@ void Heating::init(unsigned mode, const SettingState *settings, HeatingInfoServi
                     digitalWrite(HeizungPin, LOW);
                 }
 
-//                schedule_function([e]() {
-//                    Serial.printf("Error: %d\n", e);
-//                });
+                schedule_function([e]() {
+                    Serial.printf("Error: %d\n", e);
+                });
             });
 
             mHeizungTicker.attach(10, [this]() {
-                // only check if no pump cycle is active
-                if (!mPumpCycleActive) {
-                    sensor.read();
-                }
+                sensor.read();
             });
 
             break;
@@ -80,10 +76,9 @@ void Heating::handleHeatingEvents() {
         if (mHeatingStatus == false) {
             // turn off active turnoff timers
             mLuefterTicker.detach();
-            //Serial.println("heating should run now!");
-
+            Serial.println("heating should run now!");
+            // turn on heating and fan
             digitalWrite(LuefterPin, HIGH);
-
             digitalWrite(HeizungPin, HIGH);
 
             mHeatingStatus = true;
@@ -95,7 +90,7 @@ void Heating::handleHeatingEvents() {
         // if humidity too low turn off heating and fan after 60secs
         if (mHeatingStatus == true) {
             digitalWrite(HeizungPin, LOW);
-            ////Serial.println("heating should NOT run now!");
+            Serial.println("heating should NOT run now!");
             // add the heat time it took to the total
             mheatingservice->addHeatTime(Timer::getSystemSeconds() - mheatingservice->getLastHeatingStartTime());
 
@@ -105,7 +100,7 @@ void Heating::handleHeatingEvents() {
                     // turn off fan
                     digitalWrite(LuefterPin, LOW);
                     schedule_function([]() {
-                        ////Serial.println("turning off fan");
+                        Serial.println("turning off fan");
                     });
                 });
             }
@@ -126,46 +121,21 @@ void Heating::handleTimeHeater() {
         digitalWrite(LuefterPin, HIGH);
         digitalWrite(HeizungPin, HIGH);
 
-        ////Serial.println("Turning on heating");
+        Serial.println("Turning on heating");
 
         mTurnOffTicker.once((int) ((float) refreshperiod * (float) percentOn / 100.0), []() {
             digitalWrite(HeizungPin, LOW);
 
-            ////Serial.println("Turned off heating!");
+            Serial.println("Turned off heating!");
         });
 
         mLuefterTicker.once((int) (((float) refreshperiod * (float) percentOn / 100.0) + 30.0), []() {
             digitalWrite(LuefterPin, LOW);
 
-            ////Serial.println("Turned off fan!");
+            Serial.println("Turned off fan!");
         });
     };
 
     func();
     mHeizungTicker.attach(refreshperiod, func);
 }
-
-void Heating::setPumCycleActive(bool active) {
-    mPumpCycleActive = active;
-
-    // turn off fan if pumpcycleactive
-    if (active) {
-        digitalWrite(LuefterPin, LOW);
-        digitalWrite(HeizungPin, LOW);
-
-        mHeizungTicker.detach();
-
-        if (mHeatingStatus) {
-            // to add the correct time to the heat min counter!
-            mheatingservice->addHeatTime(Timer::getSystemSeconds() - mheatingservice->getLastHeatingStartTime());
-        }
-    } else {
-        mHeizungTicker.detach();
-        mHeizungTicker.attach(10, [this]() {
-            // only check if no pump cycle is active
-            if (!mPumpCycleActive) {
-                sensor.read();
-            }
-        });
-    }
-}

src/Heating.h

@@ -21,8 +21,6 @@ public:
      */
     void init(unsigned mode, const SettingState* settings, HeatingInfoService *heatingservice);
 
-    void setPumCycleActive(bool active);
-
     enum MODES {TIME, HUMIDITY};
 private:
     Ticker mHeizungTicker;
@@ -32,7 +30,7 @@ private:
     const SettingState* msettings;
     HeatingInfoService *mheatingservice;
 
-    bool mHeatingStatus, mPumpCycleActive;
+    bool mHeatingStatus;
 
     float lasttemp;
     float lasthum;

src/Pins.h

@@ -16,6 +16,6 @@
 #define TempSensorPin  D4
 
 // version info
-#define VERSION "v1.2.4-Alpa1"
+#define VERSION "v1.2.4-Alpha2"
 
 #endif //PUMPENSTEUERUNG_PINS_H

src/SettingsService.cpp

@@ -17,12 +17,12 @@ SettingsService::SettingsService(AsyncWebServer *server, SecurityManager *securi
 }
 
 void SettingsService::onConfigUpdated() {
-    ////Serial.println("switching led!");
+    Serial.println("switching led!");
 
     File settingsFile = ESPFS.open("settings.json", "w+");
 
     if (settingsFile) {
-        ////Serial.println("writing config file!");
+        Serial.println("writing config file!");
         StaticJsonDocument<256> doc;
 
         doc["waterOutageWaitDuration"] = _state.waterOutageWaitDuration;
@@ -46,7 +46,7 @@ void SettingsService::begin() {
         // Deserialize the JSON document
         DeserializationError error = deserializeJson(doc, settingsFile);
         if (error) {
-            ////Serial.println(F("Failed to read file, using default configuration"));
+            Serial.println(F("Failed to read file, using default configuration"));
             onConfigUpdated();
             return;
         }
@@ -59,7 +59,7 @@ void SettingsService::begin() {
         _state.heatLow = doc["heatLow"] | 65;
         _state.fanRuntime = doc["fanRuntime"] | 60;
 
-        ////Serial.println("read config file!");
+        Serial.println("read config file!");
 
         settingsFile.close();
     }

src/main.cpp

@@ -15,7 +15,7 @@ bool error = false;
 Ticker status;
 
 //pumpendauer maximum ticker
-Ticker pumpendauer;
+Ticker pumpendauer, wasserSensorDoubleCheck;
 
 //WifiManager mang;
 Heating mHeat;
@@ -33,11 +33,11 @@ SettingsService settingsservice = SettingsService(&server, esp8266React.getSecur
 void pumpeSchalten(bool on) {
     //    digitalWrite(4,on);
     if (on) {
-        //Serial.println("versuche Pumpe EIN zuschalten");
+        Serial.println("versuche Pumpe EIN zuschalten");
         // refresh last pump counter
         generalinfo.setlastPumpTime(Timer::getSystemSeconds());
     } else {
-        //Serial.println("versuche Pumpe AUS zuschalten");
+        Serial.println("versuche Pumpe AUS zuschalten");
     }
 
     if (allow && !error) {
@@ -45,57 +45,49 @@ void pumpeSchalten(bool on) {
             pumpcycles++;
             generalinfo.setPumpCycles(pumpcycles);
 
-            // pump cycle started
-            mHeat.setPumCycleActive(true);
-
             pumpendauer.once((float) settingsservice.getSettings()->maxpumpduration + 1, []() {
                 //erlaube keine einschaltung von mehr als 60 sek
                 if (Timer::getSystemSeconds() - turnontime >=
                     (unsigned) settingsservice.getSettings()->maxpumpduration && turnontime != 0) {
                     //error zu lange
-                    //Serial.println("\n\npumpe lief mehr als 10 Minuten durchgaengig");
+                    Serial.println("\n\npumpe lief mehr als 10 Minuten durchgaengig");
                     pumpeSchalten(false);
                     error = true;
                 }
             });
         } else {
             generalinfo.setPumpDuration(Timer::getSystemSeconds() - turnontime);
-
-            // pump cycle stopped...
-            mHeat.setPumCycleActive(false);
         }
 
         // save pump start time
         turnontime = Timer::getSystemSeconds();
 
         digitalWrite(SchuetzPin, on);
-        //Serial.println("[Erfolg] pumpe wird geschalten");
+        Serial.println("[Erfolg] pumpe wird geschalten");
     } else {
-        //Serial.println("[FEHLGESCHLAGEN] Schalten des Schütz gesperrt durch Timeout oder Fehler-- sofortiges ausschalten der pumpe\n");
+        Serial.println(
+                "[FEHLGESCHLAGEN] Schalten des Schütz gesperrt durch Timeout oder Fehler-- sofortiges ausschalten der pumpe\n");
         turnontime = -1;
         digitalWrite(SchuetzPin, LOW);
     }
 }
 
 ICACHE_RAM_ATTR void DruckschalterInt() {
-    schedule_function([]() {
-        if (digitalRead(DruckSensorPin) == HIGH) {
-            //pumpe einschalten
-            //Serial.println("\n\nDruck Sensor EIN");
-            if (digitalRead(WasserSensorPin)) {
-                //Serial.println("Wasser Sensor EIN");
-                pumpeSchalten(true);
-            } else {
-                //Serial.println("Wasser Sensor aus irgent einem Grund doch nicht ein -- sofort abschalten!");
-                pumpeSchalten(false);
-            }
+    if (digitalRead(DruckSensorPin) == HIGH) {
+        //pumpe einschalten
+        Serial.println("\n\nDruck Sensor EIN");
+        if (digitalRead(WasserSensorPin)) {
+            Serial.println("Wasser Sensor EIN");
+            pumpeSchalten(true);
         } else {
-            //pumpe ausschalten
-            //Serial.println("\n\nDruck Sensor AUS");
+            Serial.println("Wasser Sensor aus irgent einem Grund doch nicht ein -- sofort abschalten!");
             pumpeSchalten(false);
         }
-    });
-
+    } else {
+        //pumpe ausschalten
+        Serial.println("\n\nDruck Sensor AUS");
+        pumpeSchalten(false);
+    }
 }
 
 // time counter to wait
@@ -103,50 +95,55 @@ int wateroutagewaitduration;
 
 void WasserSensorCheck() {
     if (digitalRead(WasserSensorPin) == LOW) {
-        //Serial.println("Wasser Sensor AUS");
-        //kein Wasser dh timer auf 10min stellen
+        // check if water sensor is also low after 500ms and lock it then
+        wasserSensorDoubleCheck.once_ms(500, []() {
+            if (digitalRead(WasserSensorPin) == LOW) {
+                Serial.println("Wasser Sensor AUS");
+                //kein Wasser dh timer auf 10min stellen
 
-        // refresh wateroutage counter
-        generalinfo.setlastWaterOutage(Timer::getSystemSeconds());
+                // refresh wateroutage counter
+                generalinfo.setlastWaterOutage(Timer::getSystemSeconds());
 
-        allow = false;
-        //Serial.println("Schalte pumpe aus");
-        pumpeSchalten(false);
+                allow = false;
+                Serial.println("Schalte pumpe aus");
+                pumpeSchalten(false);
 
-        //Serial.println("warte 30min");
+                Serial.println("warte 30min");
 
-        status.detach();
-
-        wateroutagewaitduration = settingsservice.getSettings()->waterOutageWaitDuration;
-        status.attach(5, []() {
-            wateroutagewaitduration -= 5;
-            //Serial.print("noch ");
-            //Serial.print(wateroutagewaitduration);
-            //Serial.println(" Sekunden verbleibend");
-
-            if (wateroutagewaitduration <= 0) {
-                if (digitalRead(WasserSensorPin)) {
-                    allow = true;
-                    //Serial.println("Einschalten der Pumpe wieder erlaubt.");
-
-                    //pruefen ob drucksensor ein
-                    DruckschalterInt();
-                } else {
-                    //Serial.print("wassersensor immer noch kein Wasser --> verlaengern um 120min\n\n");
-                    WasserSensorCheck();
-                }
                 status.detach();
+
+                wateroutagewaitduration = settingsservice.getSettings()->waterOutageWaitDuration;
+
+                status.detach();
+                status.attach(5, []() {
+                    wateroutagewaitduration -= 5;
+                    Serial.print("noch ");
+                    Serial.print(wateroutagewaitduration);
+                    Serial.println(" Sekunden verbleibend");
+
+                    if (wateroutagewaitduration <= 0) {
+                        status.detach();
+                        if (digitalRead(WasserSensorPin)) {
+                            allow = true;
+                            Serial.println("Einschalten der Pumpe wieder erlaubt.");
+
+                            //pruefen ob drucksensor ein
+                            DruckschalterInt();
+                        } else {
+                            Serial.print("wassersensor immer noch kein Wasser --> verlaengern um 120min\n\n");
+                            WasserSensorCheck();
+                        }
+                    }
+                });
             }
         });
     } else {
-        //Serial.println("Wasser Sensor EIN");
+        Serial.println("Wasser Sensor EIN");
     }
 }
 
 ICACHE_RAM_ATTR void WasserSensorInt() {
-    schedule_function([]() {
-        WasserSensorCheck();
-    });
+    WasserSensorCheck();
 }
 
 void setup() {
@@ -167,9 +164,9 @@ void setup() {
 
     // initilize serial connection
     Serial.begin(115200);
-    //Serial.println("\n\n\n\nstartup of ESP");
-    //Serial.print("Version: ");
-    //Serial.println(VERSION);
+    Serial.println("\n\n\n\nstartup of ESP");
+    Serial.print("Version: ");
+    Serial.println(VERSION);
 
 
     //initial measurement of water state
@@ -191,16 +188,16 @@ void setup() {
 
 
     // initialize wifi
-    //Serial.println("Initializing wifi");
+    Serial.println("Initializing wifi");
     esp8266React.begin();
     settingsservice.begin();
     server.begin();
 
     // initialize heating control
-    //Serial.println("initializing heating service");
+    Serial.println("initializing heating service");
     mHeat.init(Heating::HUMIDITY, settingsservice.getSettings(), &heatinginfo);
 
-    //Serial.println("startup sequence complete!\n");
+    Serial.println("startup sequence complete!\n");
 }